2. Double-click „Network Connections‟ icon. 3. Right-click „Local Area Connection‟, and click „Properties‟.
4. Select „Internet Protocol (TCP/IP)‟, and then click „Properties‟. 5. In „IP address‟ field, please fill in any IP address begins with „192
If you changed the IP address of this IP camera and you forget it, there‟re 2 methods to recover it: a. Press and hold the „Reset‟ button located
6. Web Management Interface Make sure the IP camera is correctly powered (Power LED is on), and then launch Internet Explorer and type the IP addr
This IP camera requires a special ActiveX control (A.K.A. „Plugin‟) to work. Please click on the message, and select „Install ActiveX Control…‟:
Your computer may not have the display capability that this IP camera requires, or you don’t have Microsoft Dire
7. Software Installation Follow the simple steps below to run the Install Wizard to guide you quickly through the Installation process. The follow
3. The system will start the installation procedures. Click “Next” to continue installation. 4. If you wish to install the software program i
5. Click “Install” to start installing the program. 6. The system will install the program automatically.
7. Click “Finish” to complete the software installation. 8. When the installation is completed. The system will auto run ”Administrator Utilit
Multi-Languages QIG in Driver CD ================================================== Český: Českého průvodce rychlou instalací naleznete na přiložen
9. Please enter the default password “1234” and click “OK” to login to the IP setup page. 10. Internet Camera is working through the network (
11. This wizard will pop up a window to ask you if you want to run the “Camera Viewer” and see the video of the Camera immediately. Select “OK” to
8. Network Configurations When you click the “Detail Setting”, a screen will pop up for you to enter the “Administrator Name” and “Password”. The
8.1.1. Network Setting Network Setting Internet Camera Name The default camera name is “IC1500WG”. It is recommended to name a meaningful name f
Gateway The Gateway is used to forward frames to destinations in a different subnet on the Internet. The Gateway setting must be the same with t
8.1.2. Wireless Settings (IC-1510Wg Only) You must configure the wireless settings from wired environment. Then you can remove the wired cable and
After site survey procedure, there will show existing AP SSID. Then press “Connect” to connect AP router or press “Add to Profile” to configure t
There are WEP (Open System/Shared Key) ,WPA-PSK,WPA2-PSK and WPANone encryption settings. You can choose one to match AP router wireless settings.
9. Firmware Upgrade Here provides several tools to upgrade the firmware of this IP camera, clear all settings, or switch LED notification off.
Item Description Upgrade Firmware If you downloaded latest firmware file from our website, you can click this button to start to upload the firmwa
Copyright by Edimax Technology Co, LTD. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in
R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL
Content 1. Product Information ... 1 2. Check your package contents ...
1 1. Product Information Complies with IEEE802.3, 802.3u standards Complies with Wireless 802.11b/g standards with WEP, WPA and WPA2 encrypt
4. Hardware Installation 4.1. LED and Focusing The Camera head and its focus ring allow you to modify the aim and focus of the Camera. To adjust
4.2. Camera Ports The Camera features two ports and a Reset button. Antenna connector The Standard reverse SMA connector is for any antennas
4.3. Installation Procedure 1. Unpack the Internet Camera package and verify that all the items listed in the Chapter 1 are provided. 2. Connect
5. Locate the IP Address Default IP address of this IP camera is 192.168.2.3. If you wish to assign another IP address to this IP camera, you ha
Comments to this Manuals