User Manual ES-5808PHG Gigabit 8-Port 802.3at PoE Web Smart Switch
9 Figure 1-2 Configuration System System Configuration This page shows system configuration information. User can configure lots of information as F
10 Figure 1-3 ¾ MAC Address: Displays the unique hardware address assigned by manufacturer (default). ¾ S/W Version: Displays the switch’s firmware
11issued by the switch to specified trap managers. You must specify trap managers so that key events are reported by this switch to your management
12 Figure 1-4-1 Figure 1-4-2 VLAN A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain, which would allow you to iso
13devices are still plugged into the same switch physically. Port Segmentation (VLAN) Configuration ¾ VLAN ID: ID of configured VLAN (1-4096, no l
14VLAN Per Port Configuration The 802.1Q Per Port Configuration page allows you to change the VLAN parameters for individual ports or trunks. You ca
15Only.” ¾ PVID: The PVID (Port VLAN ID) is associated with untagged, ingress packets. It is assigned to untagged frames received on the specified i
16LACP IEEE 802.3ad Link Aggregation Control Protocol (LACP) increases bandwidth by automatically aggregating several physical links together as a l
17configuration message (BPDU frame). Number between 1-10 (default is 2). ¾ Max Age – The maximum time (in seconds) a device can wait without receiv
18 Figure 1-8-2 Figure 1-8-3 Figure 1-8-4
IContent Content…………………………………………………………………………………I Introduction……………………………………………………………………………..3 Product Overview……………………………………………………………………………….3 Web M
19IGMP Snooping IGMP Snooping is the process of listening to IGMP network traffic. IGMP Snooping, as implied by the name, is a feature that allows
20Mirroring Port Mirroring is used on a network switch to send a copy of network packets seen on one switch port (or an entire VLAN) to a network mo
21 Figure 1-10-2 Quality of Service (QoS) In QoS Mode, select QoS Disabled, 802.1p, or DSCP to configure the related parameters. QoS Configuration ¾
22 Figure 1-11-1 QoS Mode: QoS Disabled When the QoS Mode is set to QoS Disabled, the following table is displayed. Figure 1-11-2 QoS Mode: 802.1p
23 Figure 1-11-3 Figure 1-11-4 QoS Mode: DSCP DSCP: Packets are prioritized using the DSCP (Differentiated Services Code Point) value. The Differen
24DSCP Configuration table to a common priority queue. Use Custom if you want to set each value individually. When the QoS Mode is set to DSCP, the
25PoE Configuration Remote access and monitor the attached PD (Powered Device) status by using Enable/Disable function. ¾ PoE Enabled: POE of the po
26 Figure 1-13-1 ¾ Enable Rate Limit: Click the check box to enable storm control. ¾ Rate (number of frames per second): The Rate field is set by a
27 Figure 2-1 Detailed Statics Figure 2-2 LACP Status LACP Aggregation Overview Figure 2-3-1
28¾ Port: The port number. ¾ Port Active: Shows if the port is a member of an active LACP group. ¾ Partner Port Number: A list of the ports attached
IIIGMP Snopping………………………………………………………………………….19 IGMP Configuration…………………………………………………………………19 Mirrioring…………………………………………………………………………………20 Moirrioring
29¾ Fwd Delay: The maximum time (in seconds) the root device will wait before changing states (i.e., discarding to learning to forwarding). This del
30¾ Protocol: Shows the spanning tree protocol functioning on this port, either RSTP or STP (that is, STP-compatible mode). IGMP Status IGMP Status
31 Figure 2-6-1 Figure 2-6-2 Figure 2-6-3
32 Figure 2-6-4 Ping This command sends ICMP echo request packets to another node on the network. Ping Parameters ¾ Target IP Address: IP address of
33 Figure 2-7-1 Figure 2-7-2
34 Figure 2-7-3 Maintenance Warm Restart Press Yes button to restart the switch, the reset will be complete when the power lights stop blinking. Fi
35Software upload Select “Upgrade Firmware” from the Tools drop-down list then click on the “Browse” button to select the firmware file. Click the A
36Reset button for the factory default setting Please take the following steps to reset the Web Smart Switch back to the original default: Step 1:
3Introduction Product Overview This switch is a Web Smart Switch equipped with 8-ports PoE+ 10/100/1000BaseT(X) plus 2-port gigabit SFP. It is des
4IGMP Status VeriPHY Ping ¾ Maintenance Warm Restart Factory Default Software Upload Configuration File Transfer Logout Specifications ¾ Standard I
5¾ Product Dimensions/ Weight: 440 × 220 × 44 mm (L x D x H ) / 3.2kg Performance ¾ MAC Address: 8K ¾ Buffer Memory: 176 KB ¾ Jumbo Frames: 9.6K ¾ T
6Hardware Description This part primarily presents hardware of this switch, physical dimensions and functional overview would be described. Physical
7 Rear Panel The 3-pronged power plug is placed at the rear panel of the switch right side shown as below. Hardware Installation Set the sw
8Software Description This part instructs user how to set up and manage the switch through the web user interface. Please follow the description to
Comments to this Manuals